GRANITE FAQs

Granite needs resin treatment before honing and polishing to fill pores and fissures, strengthen weak areas, and create a more stable, uniform surface for finishing.

Natural granite slabs often contain pinholes, hairline cracks, open pores and internal fissures that may not be fully visible before processing. When an untreated slab passes through honing and polishing, the abrasive pressure can expose these defects, pull out loose mineral particles or enlarge existing cracks. This may result in chipping, broken edges, uneven polishing, dull patches or visible holes in the finished surface.

Resin treatment is carried out before the final polishing stages so that a low-viscosity epoxy can penetrate into narrow cracks and pores. After curing, the resin binds the affected areas, fills surface imperfections and reinforces weaker sections of the slab. This gives the polishing abrasives a more continuous surface to work on and helps produce a smoother, more consistent finish. Certain resin systems can also enhance the stone’s natural colour and support a deeper gloss after polishing. MBEPOXY® stone-treatment products are formulated for defect repair, penetration and surface enhancement in granite and marble processing.

Correct preparation is essential. The slab should be properly ground, thoroughly cleaned and completely dry before the resin is applied. Dust, oil, grease or moisture can reduce penetration and adhesion. The resin and hardener must be mixed in the specified ratio, applied evenly and allowed to cure fully before honing or polishing continues. For example, MBEPOXY® stone-treatment guidance specifies cleaning and drying the slab, applying the mixed material in a thin layer and allowing approximately 24 hours before polishing.

Using the appropriate MBEPOXY® granite resin helps reduce problems such as unfilled pinholes, weak crack repairs and inconsistent polishing results. The correct grade should be chosen according to the stone colour, defect size, application side and desired finish.

Yes, epoxy granite resin can be used for crack repair and slab reinforcement during fabrication.

During granite fabrication, slabs may contain hairline cracks, fissures, pinholes, pores, chips or weaker sections that can worsen while the stone is being cut, handled, ground or polished. A suitable low-viscosity epoxy resin can penetrate these defects, bond the surrounding stone and stabilise the affected area before further processing. MBEPOXY® crack-filling systems are designed for repairing minor stone defects and are formulated to penetrate narrow cracks while producing a clear finish after polishing.

For visible surface cracks, the mixed resin is worked into the cleaned and dried defect and allowed to cure before the surface is honed or polished. Pigment may be added where permitted to help the repair blend with the granite colour. For reinforcement, epoxy may also be applied to the slab’s backside, sometimes with a suitable fibre mesh, to improve support in porous, fissured or fragile areas. MBEPOXY® Bottom 63 is specifically described for repairing backside pores, fissures and pinholes while adding strength to the rear surface of stone. Vacuum-compatible MBEPOXY® stone-bonding systems are also available for internal reinforcement of permeable cracks where deeper penetration is required.

Successful repair depends on preparation. The stone must be free from dust, moisture, oil and grease, and the resin and hardener must be measured and mixed in the specified ratio. The repair must cure fully before cutting, grinding, polishing or lifting the slab.

Using the correct MBEPOXY® grade helps reduce incomplete crack filling, weak bonding, reopened defects and visible surface imperfections. However, epoxy cannot compensate for a severely unstable or structurally broken slab. Wide, moving or full-depth cracks should be assessed separately, and additional mechanical or backside reinforcement may be required before fabrication continues.

It may slightly deepen or enhance granite’s natural colour and gloss, but the correct clear resin should not hide or unnaturally change the stone’s original appearance.

The final effect depends on the type of granite, its porosity, the resin grade selected and how much material penetrates the surface. A transparent, low-viscosity granite resin normally fills pores, pinholes and hairline fissures while allowing the stone’s natural pattern and mineral structure to remain visible. On porous or dark granite, the treated area may appear slightly deeper, richer or similar to a mild “wet look” after curing and polishing. This is generally considered colour enhancement rather than unwanted discolouration.

Different applications may require different results. A natural-look repair resin is preferable when the objective is to fill defects without making the repaired area obvious. A colour-enhancing or high-gloss system may be chosen when the fabricator wants to intensify the granite’s shade and achieve a mirror-like polished finish. MBEPOXY® TDK is described as a transparent, clear stone-repair system that maintains the natural look of the stone, while MBEPOXY® High Glow Colour is specifically designed to intensify the natural colour and improve post-polish gloss.

To avoid uneven dark patches or visible repair marks, the slab should be clean, completely dry and free from dust, oil, grease and moisture. Resin and hardener must be mixed accurately, applied in a controlled thin layer and allowed to cure fully before excess material is removed through grinding and polishing. MBEPOXY® crack-filling resin provides a transparent, clear coating and may also be pigmented when colour matching is required.

For the most predictable result, a small test patch should always be completed on the actual granite before treating the full slab. MBEPOXY® offers both natural-look and colour-enhancing stone resin options, helping fabricators select a system that repairs defects while preserving or deliberately improving the desired granite finish.

No, granite resin and marble epoxy should not be treated as automatically interchangeable; some products work on both stones, but many are formulated for a particular stone type, defect and processing method.

Granite and marble differ in hardness, porosity, mineral composition and processing behaviour. As a result, the epoxy system used for one stone may not provide the correct penetration, viscosity, colour effect or curing performance on the other. Granite-processing resin is commonly selected for penetrating pinholes, hairline fissures and cracks, reinforcing the slab and supporting a consistent polished finish. Marble epoxy may be designed for softer or more porous marble, larger surface defects, colour preservation, backside reinforcement or coating applications.

The difference can be seen in the available MBEPOXY® stone-processing range. For example, MBEPOXY® Italian Marble 100 is a high-viscosity, thixotropic system intended for severe surface defects and large cracks, while MBEPOXY® ALK 21 is a lower-viscosity transparent system developed for Italian marble and Alaska stone. These products use different mixing ratios, viscosities, pot lives and application procedures, showing why one resin should not be substituted for another without checking its technical specifications.

However, certain multipurpose stone resins are suitable for both granite and marble. MBEPOXY® TDK, for example, is intended for filling pinholes, fissures and hairline cracks in both types of stone, while High Glow Colour can be used for repairing defects and enhancing the finish of natural granite and marble.

Before using any resin, the fabricator should consider the stone type, crack size, front- or backside application, desired colour effect, polishing process and required curing conditions. A small trial should be completed on the actual slab before full production. Selecting the correct MBEPOXY® grade helps avoid poor penetration, sagging, uneven colour enhancement, visible repair marks, weak bonding and polishing difficulties.

Plan for a minimum curing period of 24 hours before grinding, honing, polishing or further processing the treated slab.

At slab-processing scale, the granite should remain flat, stable and undisturbed for the full 24-hour curing period after the epoxy resin has been applied. This allows the resin to penetrate the pores, pinholes and hairline fissures, bond with the stone and develop sufficient hardness before the slab is exposed to polishing abrasives, handling pressure or fabrication equipment. MBEPOXY® granite-treatment systems such as High Glow Colour and TDK specify a resting time of 24 hours before polishing or removing excess cured resin by grinding.

The 24-hour period should be included in the production schedule from the time the resin and hardener are correctly mixed and applied. During curing, the slab should be protected from dust, moisture, water, oil, accidental contact and unnecessary movement. The surface should not be polished simply because it feels dry or tack-free; surface dryness can occur before the material has developed adequate strength for mechanical processing.

Actual curing performance can be affected by workshop temperature, stone temperature, humidity, mixing accuracy, resin thickness and the specific MBEPOXY® grade being used. Cold conditions may slow the reaction, while incorrect resin-to-hardener measurement or incomplete mixing can result in soft, sticky or unevenly cured areas. The stone must therefore be clean and completely dry, and the specified mixing ratio for the selected product must be followed carefully.

For reliable production planning, allow one complete day for curing and inspect a small edge or test area before beginning full grinding or polishing. Using the recommended MBEPOXY® granite resin and following its grade-specific instructions helps prevent premature polishing, resin pull-out, reopened pinholes, weak repairs and uneven finishing. For unusually cold workshops, thick repairs or specialised reinforcement work, additional curing time may be advisable before the slab proceeds to the next fabrication stage.

Yes, granite resin can be pigmented to match or closely blend with specific granite tones.

Pigmenting the resin is particularly useful when repairing visible cracks, fissures, pinholes, chipped areas or other surface defects where a completely transparent repair could remain noticeable. By introducing a compatible pigment into the epoxy system, the cured repair can be adjusted to blend more naturally with black, grey, brown, beige, red or other granite shades. MBEPOXY® crack-filling resin is specifically described as a system that can be pigmented, while the MBEPOXY® stone-treatment range includes multiple colour options for matching and shading granite surfaces.

The pigment must be compatible with epoxy resin. Non-water-based, epoxy-grade pigments are preferred because unsuitable colours or excessive pigment can interfere with curing, adhesion, penetration and final polishing. MBEPOXY® epoxy pigments are specially developed for epoxy systems, and different pigment colours can be combined to create a customised shade.

For the best result, pigment should be added gradually in a controlled quantity and mixed uniformly before the resin is applied. The final colour can be influenced by the granite’s natural pattern, porosity, moisture level, crack depth, resin transparency and polishing process. The uncured mixture may also look different from the shade obtained after complete curing and polishing.

A small trial should therefore be carried out on the actual slab or an off-cut from the same stone batch before treating the full surface. This allows the fabricator to check the colour under workshop and natural lighting and make small adjustments where needed.

Using a suitable MBEPOXY® granite resin together with compatible MBEPOXY® pigments helps reduce obvious repair lines and uneven colour patches while maintaining the stone’s natural appearance. Exact invisible matching cannot be guaranteed for every patterned granite, but careful colour blending and sample testing can produce a significantly more consistent finish.

Yes, granite resin is suitable for both indoor and outdoor stone installations when the correct grade is selected for the exposure conditions.

For indoor applications, epoxy granite resin can be used on granite slabs, countertops, wall cladding, flooring, staircases, vanity tops and other fabricated stone components. It helps fill pinholes, pores, fissures and hairline cracks, while also strengthening weak sections before honing, polishing or installation. MBEPOXY® granite resin systems are developed for coating and repairing defects in natural granite and marble, helping fabricators achieve a smoother and more consistent finished surface.

The resin can also be used for outdoor granite applications, including exterior cladding, steps, façades, landscaping stone and other exposed installations. However, outdoor performance depends on more than the resin’s basic bonding strength. Direct sunlight, ultraviolet radiation, rain, temperature variation, standing water and continuous weather exposure can affect the appearance and durability of an unsuitable epoxy system. For exterior work, the selected resin should therefore be compatible with outdoor exposure and, where necessary, supported by suitable UV-resistant protection. MBEPOXY® explains that epoxy systems formulated with UV-resistant additives are more appropriate for exterior applications exposed to sunlight.

Before application, the granite must be clean, dry and free from dust, oil, grease and moisture. The resin and hardener should be measured accurately, mixed thoroughly and allowed to cure completely before polishing, handling or installation. Outdoor joints must also be designed to accommodate movement and prevent water from becoming trapped behind the repaired area.

A small trial on the actual stone is recommended because some granite varieties may darken slightly or show a colour-enhancing effect after resin treatment. Choosing the appropriate MBEPOXY® granite resin for the stone type, defect size, location and exposure conditions helps reduce yellowing, weak repairs, moisture-related failure and visible colour differences.

Yes, we provide a technical product booklet, and batch-specific Certificate of Analysis documentation can be shared with the relevant shipment where required.

The MBEPOXY® technical booklet provides customers with practical product and application guidance for flooring systems such as Primer Resin, Screed Resin, Base Coat Resin, Metallic Flooring Resin, 3D Flooring Resin and Top Coat Resin. It explains the recommended layer sequence, surface-preparation requirements, moisture testing, mixing by weight, maximum application thickness, curing precautions and trial-application procedures. The booklet also summarises important product characteristics, including adhesion, flow, mechanical performance, chemical resistance, gloss and recommended application areas.

For customers who need more detailed technical information, product-specific data can be provided according to the selected resin grade. This may include the resin-to-hardener mixing ratio, viscosity or flow characteristics, pot life, working time, curing time, recommended thickness and relevant performance information. Because these values differ between flooring products, the applicable documentation should always match the exact product grade supplied.

A Certificate of Analysis, or CoA, is different from the general technical booklet. The booklet provides standard product and application guidance, whereas a CoA relates to a specific manufacturing batch or lot. Where requested, the batch reference and available quality-control details can be linked to the shipment so that the customer can maintain records for inspection, internal quality control, laboratory review or project documentation.

Customers who require a CoA, batch number or specific test parameters should mention this requirement when confirming the order. This allows the MBEPOXY® team to prepare the relevant documentation together with the invoice, packing and shipment details. Customers should retain the original container labels and batch references until the material has been used and the project documentation has been completed.

The minimum order quantity starts from 20 litres and can be increased to any required bulk quantity.

For granite-processing units, stone fabricators and exporters, MBEPOXY® granite resin can be ordered from a minimum quantity of 20 litres. Quantities above this starting MOQ can be planned according to the customer’s daily slab-processing capacity, monthly resin consumption, number of production lines and export-order schedule. MB Enterprises supports bulk supply for stone-processing businesses and provides granite resin systems for professional applications such as crack filling, pore and pinhole repair, slab strengthening, surface restoration and preparation before polishing.

The 20-litre MOQ is suitable for customers who want to begin with a manageable commercial quantity, conduct production trials or evaluate the resin across different granite varieties before moving to larger orders. Established processing units and exporters can order higher volumes based on their regular consumption. Bulk quantities may be arranged in suitable cans or drums, subject to the selected product grade, resin-to-hardener ratio, packaging requirement and dispatch plan.

Before confirming the order, customers should share the type of granite being processed, the nature of the defects, the number of slabs, the preferred curing time and whether the resin is required for front-surface treatment, backside reinforcement or vacuum processing. This helps the MBEPOXY® team recommend the appropriate formulation and estimate a practical quantity.

For exporters, packaging, labelling and shipment documentation requirements should also be communicated in advance. MB Enterprises has large-scale manufacturing and pan-India supply capabilities, with technical support and data sheets available for professional customers. Larger repeat orders can therefore be scheduled according to the customer’s production cycle, helping maintain consistent material availability without unnecessary stock accumulation.

Bulk granite resin orders are supplied in drums; tote or IBC packaging is not offered as a standard option.

For granite-processing units, exporters, stone fabricators and other high-volume buyers, MBEPOXY® granite resin can be supplied in drums. Drum packaging is practical for commercial slab-processing operations because it supports regular production, reduces the number of small containers handled at the facility and allows material to be issued according to the daily processing requirement. MB Enterprises supports bulk and wholesale supply of epoxy granite resin for fabricators, contractors and distributors.

Granite resin is generally a two-component system consisting of resin and hardener. These components are supplied separately and must be used only in the mixing ratio specified for the selected MBEPOXY® grade. Customers should not interchange hardeners between different products or transfer material into unmarked containers, as this can lead to mixing errors and loss of batch identification.

At present, drums are the applicable bulk-packaging option. Totes or IBCs are not included in the standard packaging arrangement. Before placing an order, the buyer should provide the required product grade, total volume, expected monthly consumption and delivery schedule. The exact drum configuration can then be confirmed according to the formulation, resin-to-hardener ratio and order quantity.

Drums should be stored upright in a clean, dry and covered area, away from direct sunlight, moisture and excessive heat. Their lids should remain tightly closed when the material is not being dispensed. Buyers should also retain the product labels and batch references for traceability and quality-control records.

MB Enterprises has large-scale manufacturing capabilities and supplies industrial epoxy systems in bulk with consistent batch output and technical assistance. This makes drum supply suitable for granite-processing units that require dependable material availability for ongoing slab treatment, crack filling, reinforcement and polishing operations.

Yes, sample testing is available before you commit to a long-term or bulk supply contract.

Granite-processing units, exporters, stone fabricators and distributors can request a sample quantity of the relevant MBEPOXY® granite resin before finalising a commercial supply arrangement. The sample may be evaluated through an internal laboratory test, a controlled production trial or an application on an actual granite slab. This helps the buyer verify whether the selected resin is suitable for the stone type, processing method and required finish.

During testing, customers can assess important factors such as viscosity, penetration into hairline cracks and pinholes, mixing behaviour, working time, curing performance, adhesion, hardness, colour effect and polishing compatibility. Where pigmentation is required, the sample can also be used to test colour matching on an off-cut or rejected slab from the same granite batch. For reinforcement applications, the trial may be carried out on the backside of the slab or with the customer’s regular mesh and fabrication process.

The MBEPOXY® application guide recommends completing a sample or trial application before beginning a full project. This allows the customer to confirm substrate compatibility, application conditions and the expected finished result before larger quantities are used.

Customers should share the granite type, defect size, required application, preferred curing time and testing quantity when requesting a sample. The trial should be conducted under conditions similar to the final production environment because temperature, moisture, stone porosity, mixing accuracy and polishing equipment can influence the outcome.

After the sample has been evaluated and approved, the required bulk quantity, drum packaging, supply schedule, pricing and documentation can be finalised. This sample-first approach helps reduce production risk and allows both parties to establish the correct MBEPOXY® grade before entering a larger supply commitment.

MBEPOXY® granite resin is manufactured under MB Enterprises’ ISO 9001:2015-certified quality management system.

The ISO 9001:2015 certification applies to MB Enterprises’ quality-management system and supports controlled manufacturing procedures, documented quality checks, consistent production practices and continual process improvement. MB Enterprises identifies itself as an ISO 9001:2015-certified epoxy resin manufacturer supplying specialised systems for stone processing, construction, coatings and other industrial applications.

For granite-processing units, fabricators and exporters, this certification provides assurance that the resin is produced within an organised quality framework. Important manufacturing activities—such as raw-material control, formulation, batch processing, inspection and production documentation—are managed through established procedures. This helps MBEPOXY® maintain greater consistency in properties that are important during slab treatment, including mixing behaviour, penetration, curing and finished performance.

However, ISO 9001:2015 should not be confused with a separate product-performance approval. It certifies the manufacturer’s quality-management system rather than independently certifying every granite resin grade for every possible application, chemical exposure or export market. Where a buyer requires a specific product certification, safety declaration, regulatory document or country-specific compliance record, the exact requirement should be shared with the MBEPOXY® team before ordering.

Customers may also request the available technical documentation and batch-related quality information for their selected granite resin grade. This is particularly useful for exporters, organised processing units and buyers maintaining internal quality-control records.

By selecting granite resin from an ISO 9001:2015-certified manufacturer, customers benefit from MBEPOXY®’s structured manufacturing, in-house technical capability and long-standing experience in epoxy systems while still receiving guidance suited to their particular granite-processing application.

Yes, we offer distributorship, reselling and private-label supply arrangements, with both labelled and unlabelled options available.

Granite-processing businesses, stone-product distributors, exporters and industrial resellers can discuss a supply arrangement based on their preferred commercial model. Products may be supplied under the established MBEPOXY® brand, with the customer’s approved private label, or without a retail label where the buyer manages its own branding and onward distribution. MB Enterprises’ official website specifically offers white-labelling and distributorship opportunities for businesses interested in supplying epoxy products under their own brand.

Under a distributorship or reselling arrangement, the buyer can market and supply suitable MBEPOXY® granite-processing products to stone fabricators, slab processors and other commercial customers. Under a private-label arrangement, branding elements such as the business name, logo, label artwork and pack information can be discussed before production. Unlabelled supply may also be considered for approved buyers who want to manage their own packaging or use the product internally.

The final arrangement depends on the selected granite resin grade, order quantity, drum size, packaging requirement, expected purchasing frequency and branding scope. Customers requesting labelled products should provide their proposed artwork and product information in advance. Important details such as the resin and hardener identification, mixing ratio, batch reference, application instructions and safety information must remain accurate and clearly presented.

Before entering a regular supply agreement, customers may request sample testing to confirm the resin’s suitability for crack filling, pore treatment, reinforcement, colour matching and polishing. Once the product and commercial terms are approved, bulk supply can be planned according to the buyer’s production or resale requirements. MB Enterprises also identifies OEM manufacturers and industrial buyers among the customers it serves.

First orders are generally dispatched by courier, while repeat bulk orders are shipped through an arranged transport service; order processing usually takes about 1–2 working days.

For a first order, the usual approach is to dispatch the material through a courier service, particularly when the customer is testing the product, ordering a smaller commercial quantity or beginning with the minimum order quantity. Courier dispatch provides a straightforward way to deliver the initial order and allows the customer to evaluate the MBEPOXY® granite resin under actual production conditions before moving to a regular bulk-supply schedule.

Once the product has been tested and approved, repeat bulk orders are generally shipped through a suitable goods transporter. Transport arrangements are more practical for larger quantities, drum packaging and regular supplies to granite-processing units, stone fabricators, exporters and distributors. The transporter is selected according to the shipment size, destination, service availability and the customer’s preferred delivery arrangement.

For both first and repeat orders, production, documentation, packing and dispatch preparation generally require approximately 1–2 working days after the product grade, quantity, packaging, payment and delivery information have been confirmed. Repeat orders may sometimes move more efficiently because the approved formulation, pack size and commercial details are already established. However, buyers should place repeat orders in advance when continuous production depends on uninterrupted resin availability.

The stated processing period does not include the transporter’s or courier’s final delivery time. Transit duration depends on the destination, shipment volume, route, local holidays and logistics availability. Tracking or consignment details are shared after dispatch so the customer can follow the shipment and coordinate material receipt.